feresoul.blogg.se - Brother gt 541 yellow stopped printing

#BROTHER GT 541 YELLOW STOPPED PRINTING HOW TO#

When the message "WARNING WASTE INK FULL" is displayed, prepare the new Waste Ink Cartridge, and replace it when the message “ERROR WASTE INK FULL” is displayed. If there is a problem (abnormal noise or error), turn off your printer, and check if the Wiper Cleaner and the Wiper Cleaner Cassette are correctly installed. If your printer turns on without any problem, replacement of the Wiper Cleaner Cassette has been completed. (19) Close the Front Cover, and then turn on your printer. Do not touch the Clearance Sensor (the bar above the Wiper Cleaner Cassette) it may cause a malfunction. (18) Insert the Wiper Cleaner Cassette straight into your printer. Use one side of the Clean Applicator to clean one Print Head Cap.ĭo not use the dry Clean Applicator it cannot clean ink or dust. (17) Wet other two Clean Applicators and use them to remove ink or dust from the Print Head Caps. (16) Use the other side of the wet Clean Applicator to clean the backside of the Wiper Blade. (15) Use the one side of wet Clean Applicator to clean the front side of the Wiper Blade. Use only the Wash Liquid included to wet the Clean Applicators using other liquid will cause damage to the Print Heads. (14) Wear the gloves, and wet both sides of a Clean Applicator with the Wash Liquid. It comes with the new Yellow Ink Cartridge. Make sure that the bottom of the Wiper Cleaner is set within the two projections on the Wiper Cleaner Cassette. (11) Insert the two projections of the Wiper Cleaner Cassette into the holes on the new Wiper Cleaner. (10) Carefully drop off the used Wiper Cleaner in a trash can/bag by turning it upside down.ĭispose of the used Wiper Cleaner in compliance with your local regulations (9) Push both sides of the Wiper Cleaner Cassette to open it. (8) If the ink inside of the Wiper Cleaner Cassette is soiled with ink: Wear gloves and remove the ink with a dry cloth, and then clean with a cloth damped with water.

Do not touch the Clearance Sensor (the bar above the Wiper Cleaner Cassette) it may cause a malfunction.

Do not tilt the Wiper Cleaner Cassette the ink may get on your hands or clothing.

(6) Open the Front Cover by unlocking the Cover Locks. (4) Press the Up/Down Button to select the “Cap/Wiper Clean”, and then press the OK Button. (3) Press the Up/Down Button to select the “Maintenance”, and then press the OK Button. (2) Press the OK Button to open the Menu Display. Always clean the Print Head Cap and Wiper Blade when replacing the Wiper Cleaner. The Wiper Cleaner is attached to the Yellow Ink Cartridge, and it needs to be replaced when the Yellow Ink Cartridge is replaced.

Dispose of the used Ink Cartridge in compliance with your local regulations.

Do not repeat uninstalling/ installing the Ink Cartridge.

(4) If you have replaced the Yellow Ink Cartridge, you need to replace the Wiper Cleaner attached to it. If you have installed a wrong color of ink, immediately contact Brother Customer Service Hot Line. Loading a wrong color of ink causes damage to the Print Heads. Buy Flushing Solution for your Brother GT-541 and GT-782.(3) Insert the new Ink Cartridge securely (be careful with the direction).Ĭonfirm the color of ink.

If the liquid does not go through the head at all, all of the nozzles are likely being clogged and probably less chance to recover.

Take 1.5cc of WASH liquid out of the container.

#BROTHER GT 541 YELLOW STOPPED PRINTING HOW TO#

Nozzle clogging problem found on the heads being removed from the printer for a whileįollow the photo below on how to apply WASH liquid to the head.

* Same time you need to check the wiper blade and the wiper cleaner conditions.

However, in this case smaller individual containers should be used.Įffective for the inconsistent missing nozzle problem If the WASH liquid has been already filtered following the process previously instructed, you can directly dip applicators into the liquid as needed.

Note - You may need to wipe the head surface before injecting solution into the head.ĭo not put any applicator directly into the WASH liquid container.

Attach the filter to the syringe and apply the WASH liquid to an applicator (swab).

Take a little bit of WASH liquid into the syringe with no filter attached.

(4) Apply WASH liquid to the cleaning applicators (head swabs) (3) As the photo shows put the air into the head and drain the ink remains inside of the head. (2) Take the filter off and intake the air.

This work should not be done on the heads still mounted on the printer.